Insulation Automatic cable/Optical cable tie machine

Isolierung Automatische Kabel-/Optikkabelbindermaschine

The machine is a hand-held free-to-height cable quick-attachment tool with internal components such as controllers that automatically complete all steps of cable tying.
It can be widely used in the high-altitude operation in the field of communication engineering and is used to replace the traditional manual attachment strapping cable.

Quick Details

Place of Origin: China Brand Name: XINCHENG

Name: automatic cable tie machine, Optical cable binding machine

Application: cable tying machine Feature: Automatic

Power Source: Rechargeable lithium battery Bundling range: 0-60mm

Binding : can binding 1600 times for one time fully charger. Voltage: 12V

Battery：7800 mAh/group, Fully charged, one battery can work more than 1600 times, about 3 kilometers or more

Battery installation mode: external and embedded for your choice

Attached rod：Insulated 10KV, the material is insulated glass epoxy tube, 1.2 m / root, Multiple pieces can be connected together, with a length of 10 meters

Wireless Remote control switch：remote control distance is 25 meters, can be used in partition wall

Binding time: 0.80s/time Power charger time: 1.5hours

Wire diameter: Galvanized iron wire 0.8mm, 110meter/roll; Coated iron wire (lined wire) 0.8mm, 110meter/roll

Galvanized iron wire：110 meters per plate, 300-700 mm at a time, 150-180 times per plate

Coated iron wire：110 meters per plate, 300-700 mm at a time, 150-180 times per plate

Produktbeschreibung:

The machine is a hand-held free-to-height cable quick-attachment tool with internal components such as controllers that automatically complete all steps of cable tying.

It can be widely used in the high-altitude operation in the field of communication engineering and is used to replace the traditional manual attachment strapping cable. The machine is mainly made up of five parts, body, special wire reel, battery, remote control switch and hand-held pole. The body special reels batteries remote switches and hand-held poles.

Battery: 7800 mAh/group, voltage 12V, fully charged, a battery can work more than 1600 times, about 3 kilometers or more attached.
Attached hanging rod: 10KV insulated, made of insulated glass fiber reinforced plastic epoxy pipe, 1.2 meters per piece. 0.7 kg each. Multiple pieces can be connected together, with a length of 10 meters.
Coated iron wire: 110 meters per plate, 300-700mm wire at a time, 3 kilometers or more can be attached. Wire diameter 0.8mm, strapping range: 0-60mm
Wireless Remote control switch: size 62mm*30mm*12mm, remote control distance is 25 meters in an open space, can be used on partition walls

Features:

High working efficiency In the same working environment, it’s five times as much as traditional manual work and can work for 10 hours. It independent on the external circumstances and objective factors as well as suitable for all kinds of complex cable tying. Efficiency is greatly improved and labor intensity is reduced .
High safely It is electrically insulated from the high voltage of 10 KV . Avoid to the traditional climbing ladder, pulley and other aerial work. It can improve the safety coefficient of operating personnel and reduces safety accidents, which can ensure the safety of personnel.
Easy operation of the equipment Simple and convenient remote control , it can be operated by one person independently, which reduce the use of labor force. Because of it can easy to be understand, quick to be used, the different cultural levels and different age groups of workers wide use it.
Easy to carry In the traditional construction process, it is necessary to carry the large-scale tools of ladders and some vehicle. As well as three persons can complete the work at least . The machine has the advantages of small size, light weight, detachable packaging, carry conveniently, which reduce the working time, at the same time, it can improve working efficiency.
Automatic Operation

Press the remote control switch it can be adjusted the gear (circled tight or loosen) automatically.

Usage method:

Charge the battery. The green light means full charge. The charging time is about 90 minutes. After full charge, insert the host and turn on the host switch. At this time, the buzzer will give a beep indicating that the machine has been powered on.
Rotate and remove the round cover fixing the cable tray in the middle of the fuselage, and then install the screw tray into the designated position.
Take out a coil of binding wire and straighten it by hand for 10 cm, insert it into the rectangular inlet hole of the machine body, transport it forward to the bottom, install the binding wire, and rotate the round cover to tight (if the iron wire is not straightened, it is easy to cause wire jam, and the iron wire cannot enter the specified track).
Start the machine, use the remote control to lead out the binding wire for testing, and send the iron wire out according to the specified track to ensure the successful installation of the wire reel. Warning: When the machine is working, do not touch the tie wire walkway to prevent personal injury.
Take out the insulating rod with proper height to butt with the battery insulating rod
Lift the fuselage and select the appropriate line for construction
Put all the cables to be bundled into the binding groove.
The construction personnel press the remote control switch, and the attached hanger automatically spins, hinges and cuts off.
Press it again after one operation. Do not operate it for many times continuously to prevent the two iron wires from winding together.
If the machine beeps continuously after a long time of inactivity, please restart the power supply and the machine will resume working.
Adjust the sliding block of the wire tying walkway. First loosen two screws with a tool, and then adjust to an appropriate position. Gradually reduce the diameter of the circle formed by the wire in a clockwise direction, otherwise increase it. The best diameter of wire tapping forming ring is 83-85).

Product fault and repair:

Product fault and repair:

Fault phenomenon	Contributing factors	Resolvent
The strapping machine cannot be started, and there is no response when pressing the key	1: Battery is dead 2: Battery damage 3: Poor line contact 4: Line fault	Replace the battery or charge it. If it cannot be started, open the enclosure to check the circuit or repair it
When the remote control switch is pressed, the machine is idling and there is no wire out	1: No wire in the wire reel 2: When the wire reel is installed, the wire head is not straightened	1: Replace the wire reel 2: take out the wire reel and straighten the bent wire head
Press the remote control switch, the machine does not work	1: The battery is low 2: the gear is blocked by foreign matters 3: the circuit board is faulty	1: Charge the battery 2: open the gear part and take out the foreign matters 3: repair
The iron wire cannot be cut after wire tapping	The props are worn or the outlet pressing plate mouth is worn	Replace the tool or outlet pressing plate
Press the remote control switch, only wire is drawn, not bundled	1: Hall element sensing position offset 2: Hall element is damaged 3: Line fault	1: Install the Hall element into the corresponding position 2: Replace the Hall element 3: Repair
Charger LED is not on, unable to charge	Charger fault	Replace charger
Wire deviation: when binding, the wire arc cannot be fastened outside the jaw	During binding, there is an object blocking the jaw, which interferes with the wire feeding track, causing the wire feeding deviation	Adjust the binding angle and remove the foreign matters on the wire outlet track of the jaw
Buzzer alarm	1: Leave the power switch on for more than one minute 2: The battery is dead	1: Turn off the power switch and turn it back on 2: Replace the battery

Special precautions:

When the wire reel is used about to the last one meter or so, the remaining iron wires must be pulled out along the plastic wire reel. They cannot be directly used up or cut off, otherwise the machine channel will be blocked by iron wires and cannot work. If the iron wire cannot be withdrawn, first check whether the scissors head is clamped. If it is clamped, turn the torsion shaft for several turns with diagonal pliers and it can be withdrawn smoothly.
It is normal that there may be loose winding. In addition, the new battery has no power or is not charged enough, and there are also loose winding of iron wire. Replacing the fully charged battery will eliminate the problem. Please feel free to use it.
Do not bundle cables.
Do not use in rainy days.

Packaging & Delivery:

Packaging Details:

geeignete Verpackung für den Export. Wirtschaftliches Verpackungsdesign, das Ihre Transportkosten spart.

Inside packing: Anti-moisture nylon bag + Carton box + woven belt.
Outside packing: carton box or wooden case and pallet.
According customer requirement.

Hafen: Shanghai, Qingdao, Tianjin

Vorlaufzeit: 7-15days

Please Contact Us

Fräulein: Lydia

[email protected]

WeChat: 86-13752439076 WhatsApp: 86-13752439076

Mob: 86-13752439076 Fax: 86-22-60863016

http://www.frpinsulation.com